Manitou Rotating Telehandler (MRT) rental: one machine for lifting, craning and working at height

With a Manitou roto telehandler you rent a forklift, crane and aerial work platform in one machine: the superstructure of the MRT series rotates through 360 degrees while the chassis stays in one place on its outriggers. Luibl Rental has ten MRT models in its rental fleet, with 4,000 to 7,000 kg load capacity and 17.90 to 34.70 m lift height.

On tight sites, every repositioning of a fixed telehandler costs time: retract the outriggers, manoeuvre, realign, set up again. On facades, halls and high-rise projects with many load points, this adds up over the day. A rotating telehandler serves the full circle around the machine from the same position. With the right attachment it also takes on tasks that would otherwise require a mobile crane or a separate aerial work platform.

Image of a rental machine of type TSR-4018 | Manitou MRT 1840

TSR-4018 | Manitou MRT 1840

Lifting capacity
4.000 kg
Lifting height
17,90 m
Lateral reach
15,10 m
Dimensions
5,25 m x 2,39 m x 2,94 m
Drive unit
Diesel
Image of a rental machine of type TSR-4518 | Manitou MRT 1845

TSR-4518 | Manitou MRT 1845

Lifting capacity
4.500 kg
Lifting height
18,00 m
Lateral reach
15,20 m
Dimensions
7,26 m x 2,45 m x 3,04 m
Drive unit
Diesel
Image of a rental machine of type TSR-5021 | MRT 2150 Privilege

TSR-5021 | MRT 2150 Privilege

Lifting capacity
5.000 kg
Lifting height
20,60 m
Lateral reach
18,10 m
Dimensions
6,78 m x 2,43 m x 3,05 m
Drive unit
Diesel
Image of a rental machine of type TSR-6022 | Manitou MRT 2260

TSR-6022 | Manitou MRT 2260

Lifting capacity
6.000 kg
Lifting height
21,80 m
Lateral reach
18,20 m
Dimensions
6,97 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-5025 | Manitou MRT 2550 Privilege

TSR-5025 | Manitou MRT 2550 Privilege

Lifting capacity
5.000 kg
Lifting height
24,70 m
Lateral reach
21,40 m
Dimensions
7,84 m x 2,49 m x 3,05 m
Drive unit
Diesel
Image of a rental machine of type TSR-7025 | Manitou MRT 2570

TSR-7025 | Manitou MRT 2570

Lifting capacity
7.000 kg
Lifting height
24,80 m
Lateral reach
20,50 m
Dimensions
7,67 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-6026 | Manitou MRT 2660

TSR-6026 | Manitou MRT 2660

Lifting capacity
6.000 kg
Lifting height
25,90 m
Lateral reach
21,70 m
Dimensions
8,08 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-6030 | Manitou MRT 3060

TSR-6030 | Manitou MRT 3060

Lifting capacity
6.000 kg
Lifting height
29,90 m
Lateral reach
25,70 m
Dimensions
7,94 m x 2,50 m x 3,10 m
Drive unit
Diesel
Image of a rental machine of type TSR-7035 | Manitou MRT 3570

TSR-7035 | Manitou MRT 3570

Lifting capacity
7.000 kg
Lifting height
34,70 m
Lateral reach
28,00 m
Dimensions
8,86 m x 2,50 m x 3,26 m
Drive unit
Diesel
Image of a rental machine of type Rotating Telehandler TSR-7035 ES | Manitou MRT 3570 ES

Rotating Telehandler TSR-7035 ES | Manitou MRT 3570 ES

Lifting capacity
7.000 kg
Lifting height
34,70 m
Lateral reach
28,00 m
Dimensions
8,86 m x 2,50 m x 3,26 m
Drive unit
Diesel
Mehr anzeigen

Ten Manitou MRT models cover 17.90 to 34.70 m lift height

Which Manitou Roto fits depends on the lift height and the load at the furthest placement point. The rated load capacity only applies close to the machine; as the outreach increases, the permissible load drops considerably according to the load chart. Choose the model based on the least favourable load point, not on the highest load capacity.

Up to 18 m lift height: compact for tight sites and courtyards

  • Manitou MRT 1840: 17.90 m lift height, 4,000 kg load capacity, 15.10 m outreach, 2.39 m wide
  • Manitou MRT 1845: 18.00 m lift height, 4,500 kg load capacity, 15.20 m outreach

21 to 26 m lift height: the class for building construction and installation

30 to 35 m lift height: for tall facades, industry and steel construction

All models are diesel-powered. The full data sheets are available on the individual model pages.

Roto or fixed: a Manitou Roto pays off with many load points in a confined space

The Manitou Roto shows its strength where a fixed telehandler would constantly have to reposition. For pure material handling on open, level ground, a fixed machine is usually the more economical choice.

  • Rotating superstructure: the MRT models slew the load around the machine. One position covers load points in front of, beside and behind the machine.
  • Outriggers: all MRT models have outriggers. They only reach full lift height and outreach with the outriggers deployed; this gives stability at great height but costs time with every repositioning.
  • Lift height: the MRT series starts at around 18 m and reaches up to 34.70 m. Below that, Fixed Telehandlers cover most tasks.
  • Space requirement: because the chassis stays put, the Roto needs less manoeuvring space than a fixed machine that has to drive up to every load point.

If you mainly handle pallets on level ground, you will find the right machines among the fixed Manitou telehandlers. An overview of all Manitou types is given on the page Manitou telehandlers.

With attachments the Manitou Roto becomes a crane or an aerial work platform

The roto telehandler changes its task via the attachment. Each attachment has its own load chart, which the operator must know before use.

  • Fork carriage and pallet forks: lift material onto floor slabs, scaffolding and roofs or unload trucks.
  • Load hook, winch and crane jib: the MRT works as a mobile crane and places loads over obstacles such as parapets or roof overhangs.
  • Platform: with a basket approved for the model, the Roto becomes an aerial work platform for installation, facade work and maintenance at great height.
  • Other attachments: buckets and special grabs are put together on request.

The overview Attachments for telehandlers shows which attachments fit your model. State the required attachment in your enquiry straight away, and we will schedule machine and attachment together.

Weight and outriggers decide whether the Manitou Roto fits your site

Depending on the model, a Manitou Roto weighs between 13,300 kg (MRT 1840) and 23,800 kg (MRT 3570). You should therefore check access, ground conditions and set-up area before your enquiry.

  • Access: the models are 2.39 to 2.50 m wide and 2.94 to 3.26 m high. Gates, passages and bends on the way to the set-up position must accommodate this.
  • Ground conditions: the outriggers transfer the load into the ground at specific points. On soft ground, backfill or above basement ceilings, load-spreading pads are required; if in doubt, a structural engineer decides.
  • Set-up area: allow space for the extended outriggers and the slewing range of the superstructure, and cordon off this area during operation.
  • Transport: the machine is delivered by low-loader to your site, throughout the Netherlands. The low-loader needs a paved surface for unloading.

For the Manitou Roto the operator needs additional competence

Operating a rotating telehandler requires more than basic telehandler training. In the Netherlands, the employer must ensure under Dutch occupational health and safety legislation (Working Conditions Act and Working Conditions Decree) that the operator has demonstrable competence for the machine and the application.

  • Basic training: qualifies for the telehandler in forklift mode.
  • Additional competence for rotating machines: telehandlers with a rotating superstructure require additional, demonstrable competence.
  • Additional competence for platform and lifting work: anyone working with a basket or load hook needs additional competence for each. In the basket, personal fall protection is mandatory, in line with the rules on work at height under the Working Conditions Decree.
  • Instruction and appointment: the employer instructs the operator on the specific machine and appoints them as operator.

Luibl Rental does not provide training itself, but informs you about certified providers. Find out more on the Trainings page.

FAQ: Manitou rotating telehandlers

chevronDown

How high does a Manitou Roto telehandler lift?

Up to 34.70 m: that is the lift height of the Manitou MRT 3570, the largest Roto model in the Luibl Rental fleet. The smallest model, the MRT 1840, reaches 17.90 m. Load capacity ranges from 4,000 to 7,000 kg depending on the model; at great height and outreach, the permissible load according to the load chart is considerably lower.

What is the difference between a Manitou MRT and a fixed Manitou MT?

The MRT has a rotating superstructure, the MT does not. An MRT slews the load around the machine and works from one position with outriggers deployed. A fixed MT only lifts forwards and has to be repositioned for every new load point, but is usually more economical for pure material handling.

What qualification does the operator of a rotating telehandler need?

The operator must have demonstrable competence for a telehandler with a rotating superstructure; under Dutch occupational health and safety legislation (Working Conditions Act and Working Conditions Decree), the employer must ensure this. Working with a basket or load hook requires additional competence for each. The employer also instructs the operator on the specific machine and appoints them as operator. Luibl Rental does not provide training itself, but its Trainings page informs you about certified providers.

Can a Manitou Roto be used as a crane?

Yes, with a load hook, winch or crane jib a Manitou MRT works as a mobile crane. Each of these attachments has its own load chart, and the operator needs the corresponding additional competence. Please state the attachment in your enquiry.

Can people be lifted to height with a rotating telehandler?

Yes, but only with a basket approved for the specific model. Everyone in the basket wears personal fall protection, and the operator needs additional competence for this work.

How does a Manitou Roto get to the site?

By low-loader: it is delivered to your site, throughout the Netherlands. The MRT models weigh between 13,300 and 23,800 kg and are up to 2.50 m wide. Check access, the unloading area and the bearing capacity of the ground in advance, and plan the job early so that machine and transport can be scheduled in good time.

Request a Manitou Roto telehandler: with these details we prepare your quote

The more precise your enquiry, the better our model proposal will fit. These details help our scheduling team:

  • site location and rental period
  • required lift height and the heaviest load with its distance from the machine
  • attachments, for example basket, winch or forks
  • access and ground conditions at the set-up position

You will receive a quote with model, transport and attachments at short notice. Request a Manitou Roto now.